ClearSign (CLIR) Q3 2026 Earnings Call Transcript

Source Motley_fool
Logo of jester cap with thought bubble.

Image source: The Motley Fool.

DATE

Thursday, Nov. 19, 2026

CALL PARTICIPANTS

  • Investor Relations - Matthew Selinger
  • Chief Executive Officer - Colin James Deller
  • Chief Financial Officer - Brent Hinds

TAKEAWAYS

  • Revenue -- approximately $712,000, representing a decrease from $1 million for the same period in 2025 primarily due to changes in product mix.
  • Gross Margin -- approximately 55.6%, representing an increase of almost 20 percentage points over the prior comparable period driven by a licensing arrangement with an original equipment manufacturer (OEM).
  • Net Loss -- decreased by $361,000 year over year, primarily reflecting a $601,000 reduction in general and administrative expenses.
  • G&A Expenses -- decreased by $601,000 year over year, due to the prior year's period including a one-time noncash expense related to the vesting of restricted stock units for former Directors.
  • Other Income -- decreased by $233,000 year over year, because the company's Department of Energy grant was completed in May 2026.
  • Cash Used in Operations -- approximately $1.3 million compared to $1.8 million for the same period in 2025, driven by the timing of customer cash collections.
  • Cash Balance -- approximately $10.3 million in cash and cash equivalents as of Sept. 30, 2026.
  • Common Stock Outstanding -- approximately 6.8 million shares as of Sept. 30, 2026.
  • Gulf Coast Installation -- a 26-burner system at a petrochemical facility is scheduled for startup in Nov. 2026 following a successful installation in Oct. 2026.
  • California Burner Project -- a 32-burner order utilizing a new flat flame configuration is currently in the testing and fabrication phase, with the first half of burners scheduled for shipment upon completion.
  • Delayed Texas Order -- a 36-burner project remains on hold due to internal organizational changes within the client, though the company noted the delay is unrelated to ClearSign technology.
  • M Series Order Volume -- management reported five orders in the third quarter and two orders so far in the fourth quarter, primarily serving the Permian region.
  • M Series Pricing -- burners range from $50,000 to $250,000 per unit, with recent large-size orders averaging approximately $180,000.
  • M Series Target Run Rate -- management is targeting a consistent run rate of at least 20 burners per year.
  • California Flare Project -- a complete flare system valued at $1.5 million is scheduled for startup by the end of 2026, serving as a key industrial reference for measured emissions permits.
  • Flare Target Run Rate -- management expects a long-term run rate of three to four systems per year.
  • DOE/Kern Grant -- the company was selected for an Industrial Technology Validation Program grant for a project valued between $500,000 to $750,000, with an order expected in the first quarter of 2027.
  • Break-even Metric -- management identified a target of 160 burners per year or an annual revenue run rate of $16 million to reach company break-even.
  • Refinery Cost Savings -- management estimated the cost of a ClearSign burner system at $5 million to $10 million for a refinery project, compared to an estimated $15 million for traditional selective catalytic reduction technology.

Need a quote from a Motley Fool analyst? Email pr@fool.com

RISKS

  • Deller noted, "For that, we also do not have any updates. So I don't have any news at this point," regarding a 36-burner order in Texas that remains on hold due to client organizational changes.
  • Deller stated, "I do believe that they're still completing permits, so that is a caveat on that statement," when discussing the timeline for the DOE Industrial Technology Validation Program grant project.

SUMMARY

ClearSign (NASDAQ:CLIR) reported a shift in revenue composition that resulted in increased gross margins during the third quarter. Management stated that the company is utilizing an asset-light strategy, leveraging third-party infrastructure for manufacturing while focusing on its intellectual property and engineering. The company reported the near completion of a 26-burner installation on the Gulf Coast, which management identified as a milestone for demonstrating technology at scale. Operational focus remains on commercializing process burners, midstream burners, and flare systems across North American energy hubs.

  • CEO Deller stated, "The licensing sales, we've had this as part of our plan for ClearSign, really from the start as a part of the long-term strategy, especially looking at scalability and how do we grow the business."
  • Deller noted that potential clients "are waiting to see the technology running in somebody else's heater" before committing to large-scale orders.
  • The company developed its flare and M Series designs through computational fluid dynamics, moving directly from computer modeling to field installation.
  • Management noted that the development of flat flame burners represents a technical progression toward entering the ethylene furnace and downfired reformer markets.
  • Management reported that its licensing model allows customers with manufacturing capabilities to build burners using ClearSign designs, which helps bolster the company's gross margins toward a long-term 40% target.

INDUSTRY GLOSSARY

  • NOx: Nitrogen oxides, highly regulated toxic gases produced during combustion that the company's technology aims to eliminate.
  • SCR: Selective Catalytic Reduction, an expensive post-combustion technology used to remove NOx using ammonia.
  • CEMS: Continuous Emissions Monitoring System, equipment that takes real-time measurements of stack emissions for regulatory compliance.
  • CFD: Computational Fluid Dynamics, a computer modeling technique used to design and optimize burner performance.
  • M Series: A product line of standard burners designed for midstream energy applications.
  • Gen2: The company's second-generation technology platform for industrial burners.

Full Conference Call Transcript

Operator: Good day, everyone, and welcome to ClearSign Technologies Third Quarter 2026 Earnings Conference Call. [Operator Instructions] It is now my pleasure to hand the floor over to your host, Matthew Selinger, Investor Relations at ClearSign. Sir, the floor is yours.

Matthew Selinger: Good afternoon and thank you, operator. Welcome everyone to the ClearSign Technologies Corporation third quarter 2026 corporate update call. During this conference call, the company will make forward-looking statements. Any statement that is not a statement of historical fact is a forward-looking statement. This includes remarks about the company's projections, expectations, plans, beliefs and prospects. These statements are based on judgments and analysis as of the date of this conference call and are subject to numerous important risks and uncertainties that could cause actual results to differ materially from those described in the forward-looking statements.

The risks and uncertainties associated with the forward-looking statements made in this conference call include, but are not limited to, whether field testing and sales of ClearSign products will be successfully completed, whether ClearSign will be successful in expanding the market for its products, timing of customer orders and our ability to convert proposals into orders, delays, holds or cancellations of customer projects, the performance of our products in the field and related warranty costs, our reliance on original equipment manufacturers and other third parties, our ability to obtain additional financing and other risks that are described in ClearSign's filings with the SEC, including those discussed under the Risk Factor section of the Annual Report on Form 10-K for the fiscal year ended December 31, 2025, and on our Quarterly Report on Form 10-Q for the quarter ended September 30, 2026, and of course, our subsequent filings.

Any estimates we discuss today regarding our pipeline or potential future orders are forward-looking statements and are not guidance. Except as required by law, ClearSign assumes no responsibility to update these forward-looking statements to reflect future events or actual outcomes, and does not intend to do so. So on the call today with me are Colin James Deller, ClearSign's Chief Executive Officer, and Brent Hinds, ClearSign's Chief Financial Officer. So with that, I am going to turn the call over to Colin James Deller. Colin?

Colin James Deller: Thank you, Matthew. As always, I'd like to thank everyone for joining us on the call today and for your continued interest in ClearSign. Like our most recent calls, we will use a Q&A format for this session. Some of you have sent in questions ahead of time. We did assimilate those questions into the questions that we will cover today. For the call today, Matthew will lead the question and answer session. We will go through the different business units much like our previous calls. Many of you have seen this, but you can send in questions ahead of time to our Investor Relations at mselinger@firmirgroup.com.

We'll start with Brent Hinds going over the company financials for the third quarter of 2026. Brent?

Brent Hinds: Thank you, Colin, and thank you to everyone joining us here today. Before I begin, I'd like to note that our financial results on Form 10-Q was filed earlier this week with the SEC. With that, I'd like to give an overview of our financial results for the third quarter of 2026. For the third quarter of 2026, the company recognized approximately $712,000 in revenues compared to approximately $1 million for the same period in 2025. The year-over-year decrease in revenue was primarily attributable to product mix. While the product mix during the quarter resulted in lower reported revenue, it generated meaningful improvement in gross margins.

As discussed in our Q2 conference call, we entered into a licensing arrangement with an OEM heater manufacturer to build 3 M Series midstream burners, and we successfully fulfilled our obligations under this arrangement during the third quarter of 2026. Our third quarter gross profit margin was approximately 55.6%, which is an increase of almost 20 percentage points over the prior comparable period's margin of 35.8%. This year-over-year improvement in gross margin was primarily driven by our licensing arrangement with an OEM heater manufacturer. We believe licensing arrangements like this further diversifies our go-to-market strategy and we expect to continue pursuing such arrangements to further expand our revenue channels.

We also believe licensing arrangements like this will bolster our overall gross margin and help us achieve our overall long-term company gross margin target of 40%. Now moving on to the full P&L. Our net loss for the third quarter decreased by $361,000 compared to the same period in 2025. The decrease in our net loss was predominantly driven by a $601,000 decrease in general and administrative expenses, offset by a $233,000 decrease in other income. Our G&A expenses decreased predominantly due to a one-time noncash expense in the prior period related to the vesting of restricted stock units issued to our former Directors. Other income decreased predominantly because our Department of Energy grant completed in May of 2026.

Now let's shift our focus to cash. Our net cash used in operations for the third quarter of 2026 was approximately $1.3 million compared to approximately $1.8 million for the same period in 2025. This improvement was driven predominantly by timing of customer cash collections. As of September 30, 2026, we had approximately $10.3 million in cash and cash equivalents. As of September 30, 2026, we had approximately 6.8 million shares of common stock outstanding. And with that, I'd like to turn the call over to Matthew Selinger.

Matthew Selinger: Brent, thank you for the financial overview. And Colin, thank you for joining me today here. I'd like to start the call with a brief overview of ClearSign, Colin, what we do, how we do it for any new investors. After that, I think we'll dive into the product lines and company developments. So with that, Colin, could you summarize briefly for a high level, what does ClearSign do?

Colin James Deller: Yes, certainly. So really high level, right? We have unique IP and some leading engineers with the company. In essence, we provide a technologically advanced solution to enable energy companies to efficiently meet their clean air emissions obligations. So our clients are large oil refineries, petrochemical companies, midstream gas companies, generally companies in the energy business, right? As part of their production, they burn fuel gases, right, natural gas or gas blends, to make their process work, whether it's heating up oil to break it down or whatever. As part of that combustion process, they make toxic gases and we're primarily concerned with NOx emissions. These are nitrogen oxides. These gases are highly regulated.

They have to operate within them to stay within their permits. They're controlled by the local air regulators. And the traditional technology that allows them to get down to the latest levels we're seeing in California and Texas is they call a selective catalytic reduction unit. This is a very expensive piece of equipment that has to be built into the back end of the heaters and then it has to be supplied with ammonia to operate. With our unique technology, we can provide special burners that essentially do not make the NOx emissions in the first place. So you might be -- we've all had kids.

You might compare it to your kids and explain to them, hey, it's much better not to make the mess in the first place than to have to go to the expense of cleaning up afterwards. To put some numbers to that, one of our -- talking to customers from one of our projects that we have to date, for their project, their estimate to put an SCR and solve their problem that way was $15 million. Using the ClearSign burners, we believe their total cost to be in the region of $5 to $10 million. So we're looking at an 80% cost savings for that plant.

If you look at a large refinery, they probably got 40 to 50 heaters on that refinery. That savings will add up to hundreds of millions of dollars for that refinery if they apply across the site. So there's a very meaningful opportunity for our customers.

Matthew Selinger: All right. So again, I know our technology has been referred to before, kind of maybe as a simple but elegant solution. So like you said, again, we basically have a call it a better combustion, better flame, that doesn't then produce these emissions in the first place.

Colin James Deller: Yes.

Matthew Selinger: Yes, fantastic. Then, that sounds simple enough. Then how does ClearSign go about getting these solutions into the market?

Colin James Deller: Yes. So this has been a key part of the strategy of ClearSign, certainly since I joined. We have a very unique technology, obviously. We manage our sales, we have significant engagement with customers. But to provide the burners in this industry, there are some what would be typical barriers to entry. You've got to be able to demonstrate your equipment operating at full scale. Plants like oil refineries require you to manufacture equipment in shops that they have accredited themselves. Setting those up is a very cash-intensive business. We are judicial with our investors' money. We understand that's how we exist today. So we formed a strategy we call asset-light.

Essentially we focus on the IP and we have formed collaborative relationships with other companies that have the infrastructure we need that allows us to benefit from their infrastructure without that being either a capital cost or an ongoing cost for ClearSign.

Matthew Selinger: Great. So again, simplifying again, you're basically leveraging existing businesses or infrastructure to bring kind of our advanced technology solutions to market.

Colin James Deller: Yes.

Matthew Selinger: Okay. All right. Well, let's go ahead and move, if you don't mind, into the product lines. Does that work?

Colin James Deller: Certainly. Yes.

Matthew Selinger: And I think it makes sense to start with process burners here. We have a growing number of installations in the field, but in particular, we've been talking about a 26-burner order going to a Gulf Coast facility of a petrochemical customer for some time. And again, this installation was slated to start at the end of October and be operational here in this month. So I think everybody's waiting, especially our investors that follow us. How is this going?

Colin James Deller: Everyone is waiting for this, yes. It's going great. The -- you said the burner was due to install in October, that went absolutely smoothly, and they're due to start up in November, and I believe we're ahead of schedule on that timeline. It's looking really good. I think we'll be done within about a week. I'm really looking forward to having that done.

Matthew Selinger: All right, and then again, so how, on this installation, either like or unlike others, how are we going to be able to kind of claim or I guess signal a victory to the market and maybe an industry?

Colin James Deller: Yes. In terms of the event, if you like, this is different. This is a big, sophisticated heater on a global chemical company. So in these big installations, the equipment is monitored on a continuous basis. They have a system they call, known as CEMS, Continuous Emissions Monitoring equipment, and that takes continuous measurements of the emissions going out the stack and actually live streams it down to the air board, and of course to the operators and to the site there. Those analyzers are calibrated and certified by the local air board, and that is the formal measurement.

So we will be watching as will everybody else watching those numbers to ensure that they are down below the permit and the guaranteed levels at the end of this project. So that will be the success. And then for anyone looking at ClearSign, we have been focused on getting this project done and excited about it for so long that you will see LinkedIn announcements and in-time, presentations and other materials, but the data from those emissions monitors will be the metric, if you like, the event that everyone's looking forward to for the technical success of this installation.

Matthew Selinger: Right, and you said yourself, we put a lot of weight in the startup. So what do you think this means then for ClearSign's prospects going forward? And how are we going to, in a sense, leverage this?

Colin James Deller: I think this is -- I mean all the time we've said that this is huge or really meaningful. We're talking and have been talking for a long time to heater companies and importantly the lead engineers of the major refiners needing to comply with local emissions regulations. They understand the value of our technology. They understand what we do. Many of them have been to see our burners at the test furnace. The only thing they're waiting on is having a place to go see it. It's like -- almost like test driving a car or speaking to someone that's running it, so they have the confidence to recommend this product for themselves.

We've had, literally, the words of one of the leading engineers for major refinery say, I want to be the first, second person to use your burners. This reference is a major installation on a global chemical company in the middle of our biggest market down on the Texas Gulf Coast. It's been engineered by the premier heater engineering company in the country, Birwelco. I mean, while we can't name the customer on the job site publicly, but within conferences like the American Petroleum Institute that we go to, people are aware of this project. They've been watching it. So this is a really big deal for ClearSign. I'm very excited to have this done.

Matthew Selinger: So it's obviously a big catalyst. Then, I mean, investors are going to want to know, Colin, I guess, what are the next actionable items internally? I mean are we just going to let this kind of trickle out to the market? How are prospects going to know about this?

Colin James Deller: Yes, there will be many events. I mean, key among these I already -- I was down at the American Petroleum Institute last week and already talking to the lead engineers on our refiners. They're aware that this project is starting up. When we get this project operating successfully, I personally will be making phone calls to those people explaining what we've done, trying to talk them to come and see it, try to set up arrangements for them to witness it on the job site. I think my arrangements beyond that, I'm looking forward to conference presentations, magazine articles. Please ask anyone to follow us on LinkedIn. We will be putting information about this.

Obviously, this will be a multi-layered approach, but it will start with these one-on-one phone calls. I mean, there are certain key people in the industry that have talked to us about all the projects they're waiting for. I mean, they are going to be called and talked to. They'll be engaged in conversations as soon as we can get them on the phone.

Matthew Selinger: Okay. Well, thank you. That's what the investor is going to want to hear. So let's come back, and you did talk about a proposal pipeline, but I'll come back to that later, I think. Let's talk about other projects, right? We've got another notable project in process, a 32-burner order, and this is slated for California. What's the status of this project today?

Colin James Deller: So this one is going really well. In the big picture, the phase that we're at, we had a detailed engineering and testing phase that is almost down to completion. It's pretty much done to the point of discussing the witness date with the client. And from there, we'll be moving on to the fabrication of the burners to ship the first half of the burners out to the job site in California. The plan is to get those out and get those up and running and then to roll in and supply the second half. Just to, if I can, to talk a little bit more about this one.

This project's been in the test furnace a bit longer than the standard 2 to 3 weeks. The reason is this is a new configuration of our Gen2 technology platform. So when we developed that Gen2 burner, we described it as a technology platform that's adaptable and usable for different installations. This is the burner in that flat flame configuration, right? So it's the first one with a flat flame. This expands our market to get us into a new section of the heaters on refineries, often the larger heaters. As we're going through this, we're adapting the flame to be optimized in that heater.

From my perspective though, why -- additionally why we're putting a lot of effort into this is I see this as a stepping stone to get into new markets for ClearSign. But we've talked in the past and I'm sure we'll talk again about high temperature applications, downfired reformers often for hydrogen production, ammonia production, things like that, and also for ethylene furnaces. The ethylene furnaces are flat flame burners. The burner we have today is not suitable as it is for ethylene furnaces, but it is a significant step in that direction. And I think sets us up well to get engagement and start formally pursuing that expansion of our business.

Matthew Selinger: Okay. So I'm just going to back up and maybe unpack this. So obviously, and we talked about this in other calls, but the implication here because of this different configuration, right? Is that A, it's a different implication for process burners which we're already going through on this project, right? And demonstrating we can utilize this in a different type of...

Colin James Deller: Yes.

Matthew Selinger: But beyond that, in particular, this means, as you mentioned, this could enter us into other markets. You mentioned downfired reformer, ethylene and these are massive markets, as you've talked about in the past, right? If you could just give a little color, the size of these in the market and the heaters.

Colin James Deller: Yes. From my experience, though typically the ethylene business for a burner manufacturer is as big as the refining business. So it will double our market size, that in itself. The downfired reformers, these units can be up to over 200 burners in a single...

Matthew Selinger: Massive.

Colin James Deller: So again, both of these are very big burners. The great thing is when you're making burners, whether it's ethylene or multiple furnaces side by side, or the downfired reformers, you're building hundreds of burners exactly the same.

Matthew Selinger: Yes. Okay. This could be looked at maybe a stair step towards that. What else would be needed for ClearSign to go into those markets?

Colin James Deller: Yes. There is significant work that will go into developing the burners. We call these high-temperature applications for a reason. These furnaces are very hot. There will be research and development significant to develop these products. Now going into this kind of a program, you really want to do that with a customer partner who is all into the projects. So you make sure you're developing the right product, you're developing it as this customer needs it. And then at the end of the project, when you have it, you want -- that means you've got an installation lined up to put that burner into service and to demonstrate it and essentially to launch the product line.

So there will be a number of pieces that go into getting these projects. But for me, we really want to get a customer partner engaged in this development. So we can be assured of having a properly developed product at the end. We want the input, and we want a home for that first installation.

Matthew Selinger: And has the company had any conversations with potential partners?

Colin James Deller: Yes, I mean we -- this is a -- it's been part of our long-term strategy. We get the process burners done first. But no, we are -- we have been actively talking with various people and entities about this project. We don't have anything formal arranged at this time, but it is a project that we are actively working on.

Matthew Selinger: Okay. Well, it's exciting. Let me get back to process burners, if you don't mind. Then we also have announced a 36-burner order, and this was going to Texas as well. But we mentioned in the last call, this one's been delayed a bit. Is there any change of status?

Colin James Deller: There is not. I mean, again, just to iterate for anyone, we do not believe and we have been told this has nothing to do with ClearSign. It is due to internal organizational changes within the client. But for that, we also do not have any updates. So I don't have any news at this point. I just look forward to getting this project back on track.

Matthew Selinger: Okay, well then, so just a few weeks ago, it was actually the last day of the quarter -- the third quarter, September 30, you announced along with Kern Energy, that ClearSign had been selected for the DOE Industrial Technology Validation Program for a grant there. Could you give a little more color on this?

Colin James Deller: Yes. This is -- it is a nice project, I think it's a great initiative from the DOE. This is a joint project between us and our long-term customer, Kern Energy. Basically, it's a DOE-funded project for a -- to pay for the installation of one of our latest Gen2 process burners into a heater on the Kern Energy site. It's going to be a fast-turn project. The DOE will provide the money. Kern will place a full purchase order on ClearSign with that DOE money. So it's an order for us. It gets another reference out in the field. So it's, yes, a great little project for us.

Matthew Selinger: Great. And I do want to highlight, though, while we are not waiting on this, quote, "validation," right? So this will be an additional validation or data point, right? This product is already out.

Colin James Deller: We have many, many quotes using this burner technology. We demonstrated it to industry. But, extra sites having the equipment up and running in addition to the order and the revenue, but it's...

Matthew Selinger: It would be a great reference...

Colin James Deller: A win for ClearSign and a great support, a long-term customer like Kern.

Matthew Selinger: Great. So in terms of looking at the process burner product line, what do the prospects look like? We talked about the proposal pipeline in the past. How is that still looking today?

Colin James Deller: Yes. I mean, these prospects are changing rapidly as we complete this project down in Texas. So this is really exciting times for us. We have talked in the past a lot about the one customer who has identified 10 heaters they want us to look at. There's other clients that we are installing burners into that have referenced more heaters they want to look at. When those are done, there's other refinery heaters resulting from the demonstration and other sales activities that we have quoted to. So there are a lot of proposal opportunities and clients that we are in discussions with about that heater, very much focused on this Texas startup to give them confidence.

So this is really exciting. Just the timing right now is a really big deal. And yes, we're thinking in about a week, we will have that Texas site ready to talk about.

Matthew Selinger: Okay. And then when you say heaters, obviously you mentioned again, one company with 10 heaters or so, I think we mentioned this in the last call. A good number, and is it an average number of burners, saying 10 burners? I know they could be 10 to 30, something in that ballpark.

Colin James Deller: I mean, that is fair. There are some smaller heaters with 3 to 5 burners. But if you look at the orders we have in-house right now, there's 26 we are starting up down in Texas. There's 32, the flat flames we are sending out to California. The one down in Texas that's temporarily on hold was 32 burners. So yes, a heater is typically going to be -- when we look at revenue numbers, $2-plus million for ClearSign.

Matthew Selinger: Well, let's turn to the M Series then next, if you don't mind. This is the midstream product, and it seems that this has been growing into a steady stream of business. We had 5 orders in Q3, 2 so far already in Q4. Where is this business coming from?

Colin James Deller: I mean, geographically, these orders are all coming out of the Permian region, West Texas area.

Matthew Selinger: But we've shipped, is that correct, burners to other geographies and then are you seeing other -- interest from other places as well?

Colin James Deller: We are. We have burners, yes, in Oklahoma, here in Texas, 1 in New Mexico going into energy installations. We have quotes into the Marcellus area of the Northeast region. We have quotes into Canada. So we are seeing a much wider interest. The recent orders that we've processed, the 5 last month and 2 this month, are all going down to the Permian. So in terms of if we're going to go and set up a presentation somewhere, the big market right now and the growth is coming out of that Permian area, which is having these burners going down there for reference right to that region also is very powerful.

Matthew Selinger: And new heaters too.

Colin James Deller: Yes. So key, I think differently from other industries, the midstream area is growing rapidly. I believe the growth was over 20% last year. This is for gas for export, it's for gas that's going into increased utilization. If you think of all these data centers we keep hearing about, they need gas to generate their electricity. So, there's a massive demand for gas and the growth of midstream industry. So these -- in fact, I believe all of these recent orders are new heaters going down to expansion of the assets down in the Permian region.

Matthew Selinger: And these orders seem to turn a lot quicker, isn't that right?

Colin James Deller: Yes. Certainly much faster than the process burners. And the strategy we set this up was these are standard products. They are designed to be repeated and off the shelf. And we've got a sufficient frequency now, and our clients have standard heater sizes so that these -- the drawings for these orders and the engineering is already done. So we get an order, our vendors already have the drawings for these recent sizes, we are able just to produce more burners. So we get to the point of achieving the efficiency that we had envisioned when we formed the strategy for this product line.

So with that, the timing, we can turn these orders now in about 3 to 4 months.

Matthew Selinger: Yeah. I mean, I think...

Colin James Deller: Once we see the order.

Matthew Selinger: I think we saw that. I think we saw orders, as Brent mentioned, we had orders in Q2, obviously shipped and booked in Q3, right? So these are going to be much quicker. And theoretically, we could have -- we could fulfill one within the same quarter. I don't want to get aggressive. But when you talk...

Colin James Deller: If we receive it in the first week of the quarter, it is feasible for us to turn it in that quarter. The two we've received this month, the company, the client has a request date. They'll be shipped out in Q1 2027.

Matthew Selinger: And you alluded to that in the last press release, if [indiscernible] talking about those said efficiencies in the manufacturing process.

Colin James Deller: Yes. I mean, for us, the consumption of our resources is minimal. Now, we've got the work done. But we obviously place the order overseas for inspections and shipping and things like that, but the engineering of the design work is already done.

Matthew Selinger: Okay. Let's talk some numbers, Colin. What's the dollar range that these burners are selling for?

Colin James Deller: Yes, these are a wide-ranging product. In dollars from our standard sizes, they run from about $50,000 up to about $250,000 per burner. To put the current orders in perspective, the -- most of these are a large size. They're not the largest, but they're running in the $180,000 range.

Matthew Selinger: Okay. That's great. And then so what sort of run rate do you think we could -- was obtainable that we could see in this product line?

Colin James Deller: I think we've got some data to give us confidence. In last quarter, we ran about 5 burners. We've already got 2 in for this quarter. The quarter's not over yet. My goal for these products down in the Permian Basin, when we get these up and running, is to just be the go-to 9 ppm midstream burner supplier, right? If we get them proven, I think that's very achievable. I see no reason we shouldn't expect to at least maintain that 5 per quarter run rate of around 20 per year.

Matthew Selinger: Okay, perfect. All right, let's take it over to flares, if you don't mind. What is the latest development kind of on the flare product line?

Colin James Deller: Yes. This is similar, really across all of our product lines. So we've had -- we've talked about this. This year has been getting -- we standardized -- we got our products worked out, and getting the big installations out running. So like the Gulf Coast process burners like that. But we've actually got great M Series out, but getting those out, established in the industry. And it's the same for flares. Our biggest flare system is out in California. It's just about complete. It's scheduled to start up by the end of the year. This will be a great reference because we know that, that client has permits in progress that reference ClearSign Technology.

We believe they're waiting for this startup to proceed with other flares, just really the same situation we are with the others. So this start-up is going to be very significant for us. But this is a -- right, also our -- we've also talked about taking the flare as a burner product and turning it into a full $1 million system. This is a $1.5 million project of a complete flare system that ClearSign is now starting up in California and really showing, hey, we are a flare supplier.

Matthew Selinger: Yes. So, similar then to the, like you said, the 26-burner order, kind of demonstrating this full system, you believe will be a catalyst.

Colin James Deller: Yes. I mean, this is a big, very credible flare in the industry. Getting this up and running and what's rare amongst the flares is a flare that can actually meet a measured emissions permit for NOx is going to be very special in the market. So this is a big deal.

Matthew Selinger: Sure. And this product line, I mean, it's not going to turn as quickly as, let's say, the M Series, right? But what's -- do you have a target or a desirable sell rate, you think over a year on these?

Colin James Deller: Yes, desirable is a different thing, actually. I think being seeing the -- what we're seeing, right, this is a fairly local product, predominantly in California. There's been a little bit of interest in other places. I think it reasonable to look at 3 possibly 4 per year as a run rate based on what we're seeing right at this time. This one will be lumpy. The nice thing with the midstream is that there's enough volume now and they're fast enough, I think we can start to see a smoother supply of those. Only the flares are going to be on an individual basis. So it may not be so steady.

But I think for long-term run rates, that is probably a fair expectation based on the technology and the markets where they are today.

Matthew Selinger: Okay. So I want to bring all the product lines together, if you do not mind, Colin, because we are nearing the end of the year. But are there milestones we can look for between now and the end of the year, or do we jump to 2027?

Colin James Deller: No. I mean, when we talked about some of these, but [indiscernible], hopefully within a week, we are going to -- we're making phone calls about that Texas project. By the end of the year, we will get the flare started up. The way the midstream industry has been performing and being productive for us, I'm hoping we are going to get some more midstream orders before the year is out. Within the more strategic long-term developments that we are making at ClearSign, there are -- as I have alluded to, there are conversations we are having trying to put the plan together for moving into things like the high-temperature burners.

There is certainly internally, whether it is something we are going to announce or not, but I am certainly looking to make progress on those projects before the year end as well. We have got a lot to do this year. We have not finished yet.

Matthew Selinger: Okay. That's great. Well then how about -- thank you for that. How about 2027? Let's talk about next year. I know you spent time to talk about the pipeline, and we put some pieces together here in this conversation, but what do you think '27 could look like for ClearSign?

Colin James Deller: I'm excited about next year. I mean, we've really gone through this year focusing on getting these major startups and references out, operation in the field, talking about those. But we have brought that together and this year we are right in the final stages of wrapping that up. So next year is the time to get the benefit of those. So we will be out promoting the Texas installation, having that great reference in place. I am looking to bring in process burner orders next year.

Matthew Selinger: Yes, converting...

Colin James Deller: That reference in place, bringing the people in. Yes. Converting those, let's get moving on those projects. I am looking for process burner orders. I am looking to follow on from the flare installation, and I am really excited about the midstream, getting these burners that we've seen going out to midstream. Many of those are scheduled to start up in Q1, some in Q2. That will give us functioning burners down in the Permian Basin in these big installations. I said I want to be the go-to supplier for those burners. I think we have got a fantastic technology in the M1 burners.

But I don't want anyone to have any questions why they should not just order them from us. I'm really looking forward to developing a steady stream of M Series burners.

Matthew Selinger: It would be safe to say that 2026 was really kind of, lack of a better word, establishing product line, and 2027 would be converting -- conversions to those products...

Colin James Deller: Yes, right, that is a high-level look. That is what I'm saying, that we have truly talked about that, right, getting these major installations focused on developing technology, the demonstration of the Gen2 burner early in the year, focusing on the startup of the Gulf Coast, which is occurring as we speak. So yes, I think that's -- we're really looking forward to getting out and using those references to validate our technology and start to give our customers the confidence to move forward with their promotion.

Matthew Selinger: So with that, let me ask you this thing, Colin. How is the ClearSign team doing? What's the internal sentiment?

Colin James Deller: They're excited. I mean, the more we've got going on and the work they've -- so if you just look back over the last month or 2 months, but we've had a team down on the Gulf Coast site going through the installation, checking that out, going through the startup with the operators, working with the client and the work with the engineering company. And at times, that's been around the clock, so we've truly had a team down there. At the same time, we've been running multiple burner tests at Zeeco. So our engineering team, we have a lean team here. We're asset light. Everyone wears many hats. They really dig deep and do what they've got to do.

We have Brent and his finance team, and that have been out promoting midstream burners at a midstream event, showing off their amazing sales skills, right? So we've truly had all of the company doing what has to be done. We're very careful within the company to have frequent weekly communications to keep everyone up to speed on all of our projects, what we're doing, where we're going as a company. I believe everyone's really excited right now. They're seeing the success that we're getting using from Texas. We're seeing the steady stream of midstream orders coming in. Guys lined up waiting to go and start the flare up out in California. So yes, people are excited here.

I mean, they're working hard, and I really appreciate that.

Matthew Selinger: Did I hear you correctly, saying that even Brent was out on the sales calls?

Colin James Deller: Yes, Brent and the whole sales team. Everyone was out. I think the office was pretty much empty.

Matthew Selinger: Was that -- and I wonder, can I attribute the uptick in the gross margins of this month to that, Brent?

Brent Hinds: Yes, you certainly can.

Matthew Selinger: Okay, great. So with that, there are no more formal questions from my side. We are going to go and open it up, if we could, operator. We will take a pause here, but could we please open it up for question and answer session?

Operator: [Operator Instructions] Your first question is coming from Sameer Joshi from H.C. Wainwright.

Sameer Joshi: Just a few on gross margins and then order flow. The gross margins this quarter were better and I saw some reference to licensing arrangement contributing to this. Can you explain that a little bit more?

Colin James Deller: Yes, I can. Sameer, thank you for the question, first of all. The licensing sales, we've had this as part of our plan for ClearSign, really from the start as a part of the long-term strategy, especially looking at scalability and how do we grow the business. It's also one of the benefits of product lines like the midstream burners in this case, where we have standard products and we have clients that have the ability to manufacture their own burners. What's special to ClearSign is the IP and the designs. So in this case, we are able to provide the fabrication drawings to the client on a licensing basis to give them the ability to fabricate their own burners.

The benefits for the client are they get to manage the schedule. It obviously saves them money because we're not paying a third party to fabricate the burners. For ClearSign, we make exactly the same profit, whether it's a license sale or whether we are supplying the equipment. Of course, so the -- it's really been a win-win. The burners the client manufactured look fantastic. I actually got to see them myself. We also put some photographs on LinkedIn. If anyone's following us, they've been shipped down to the Permian Basin. So that went really well. We believe that the client will continue to purchase the burners for their use in that way going forward.

And it's been a very good development for ClearSign, as you saw in the margins.

Sameer Joshi: Should we expect, or let me ask it this way, are there other and more customers who are looking at this model? Or is it only this one customer that is looking to manufacture it themselves?

Colin James Deller: We certainly expect repeat orders from this customer. I don't know the plans of other customers. I would certainly be open to it. One of the criteria, of course, is they have to have the ability to manufacture the burners themselves, but I'm absolutely open to that at this point, though I've not had any other discussions about this type of order with other customers, as I said, not at this time, but we certainly expect more orders in this manner from this one customer.

Sameer Joshi: Understood. And then moving on to the M Series, I think it was mentioned that you had 5 orders in 3Q and 2 orders in 4Q so far. Should we expect additional orders in 4Q that you may announce? And I think you did address how 2027 looks for that. But how should we look at the order flow going into the end of the year?

Colin James Deller: Yes, I absolutely -- I mean, for us, the year is not over yet. We have a lot of ongoing interest in the midstream burners. And one of the -- what actually makes these questions hard to answer specifically is we have orders coming in that we have not specifically quoted, but we have sufficient -- we've given our customers sufficient details of our standard burners that match their standard heaters. So they are now quoting their standard heaters, including our burners, on opportunities that they've not necessarily told us about. So we have actually received purchase orders out of the blue that we've had to log into our system without having a prior quote.

So given that and given the conversations we're having and the amount of interest we're seeing, I don't have -- I can't make any guarantees, but yes, I am expecting additional orders for M Series burners before the year is out, just given the nature of the industry and the rate that we've seen these orders come in and just the general interest in the industry.

Sameer Joshi: And just one last one maybe for Brent and maybe I missed it in the commentary, but in addition to operating expenses being lower year-over-year, they were lower sequentially as well. So was there an explanation given for the sequentially lower OpEx?

Brent Hinds: Yes, if you look in the MD&A section of the Q, you'll see the information. It's really driven by the vesting of restricted stock units, which were noncash, and legal expenses as well, the reduction from 2025 into 2026.

Operator: [Operator Instructions] Your next question is coming from Peter Gastreich from Water Tower Research.

Peter Gastreich: Congratulations on the quarter. It's good to hear the Gulf Coast burners are up and running, and nice to see the M1 orders keep coming in. So, my first question is about the DOE and Kern Energy. So this program looks very interesting. Could you give us a sense of the size of the opportunity and roughly when the burners would go in?

Colin James Deller: Yes. But this is a fast-turn project and a chance to get our new Gen2 technology out into the field. We're able to address a particular need on this job site. So it's a single-burner heater. There's a lot of engineering involved in the order. I don't have the specific numbers to hand, but it's in the range of $500,000 to $750,000 from memory. If I'm -- I apologize in advance if I'm off with that. But from seeing the contract documents, I believe those numbers are accurate.

Peter Gastreich: Okay, great. Sorry.

Colin James Deller: So you asked about the timing and I'll tell you my expectations. We've completed the contractual details which involve the other representative of the DOE. We still have to work out the exact schedule with Kern. My expectations are that we will receive the order from them early Q1. I do believe that they're still completing permits, so that is a caveat on that statement. With that, my best guess will be to complete the order somewhere around late Q3, early Q4 next year. Again, those are estimates on my part. We've not worked out those details yet, so they may change. But that's my expectation for the progression of that project.

Peter Gastreich: Okay, great, thank you. So most of my detailed questions that I had in mind have been answered, and I appreciate that. So I just have a couple of bigger picture questions for you. So your team has talked about burners that improve yield and uptime, not just cut the emissions. So are there customers that are just generally starting to see ClearSign as a way to improve plant profitability? And could that open additional markets that aren't necessarily driven purely by NOx rules? Or is that not the right way to look at it?

Colin James Deller: No, that, Peter, is exactly the right way to look at those opportunities. And really what's exciting is if we can improve the yield or improve the uptime for a client, we're no longer just a cost for compliance with emissions, we actually give them a significant return on their investment. The Texas project that is currently on hold, unfortunately, was actually based on improving the uptime of that furnace as one of the primary drivers. So that was one project that's been through the engineering, we completed the CFD modeling, and we're able to demonstrate those benefits to the customer at that phase. So it's -- yes, it is something we're pursuing.

It's something we've been able to demonstrate to our client. And going forward, as we're able to show more and more to the industry what we can do, my expectation is that we will be able to capitalize on that ability to a greater extent.

Peter Gastreich: Okay. And just a final question. So your CTO, Matt Martin, he mentioned on our podcast a little bit ago that the M Series and the flare design went straight from computer modeling to the field. I just want to ask, how does that change the cost and speed of bringing new products to market and where does AI kind of fit in with ClearSign?

Colin James Deller: First question's easy. The ability to design a burner in CFD to the extent that we can create fabrication drawings and send it out to the field and have the success we've had on the M1 burner is a game changer. It typically takes probably an additional 6 months to a year when you're going through the slow process of optimizing a burner in a test furnace, and then you have to wait for mechanical changes to be made and then fire it up. In the computer, you can check out different ideas. You can see what's going on inside the burner and inside the flames.

And then rather than speculating what changes you need to make, you can actually see what's going on and make surgical changes to optimize the process. So the -- anyone doesn't know this, the very first M1 burner was drawn from the output from our computer modeling program. It was put in a heater, and that design has never been touched. And that burner has actually demonstrated NOx down below 2 ppm. It is still out there running today and is the benchmark for our entire M1 product line. So this is one of the -- I'm just going to brag a little bit on our CTO, Matthew Martin, the resources here at ClearSign.

We've been able to develop the computer modeling technology for combustion systems and burners, I believe, to the greatest extent anywhere in the world in my opinion, and that has allowed us to bring technologies like this to market in the speed that we have and to actually put them out in the field and have the success we've had both with the flare and the M Series. But to answer your basic question, it is hugely significant for ClearSign and the speed that we can bring not only new technologies, but also adapt technologies for specific client needs and show them how those products will work modeled inside their furnace as part of our sales or project validation process.

So it is extremely powerful.

Peter Gastreich: Great. And congratulations.

Colin James Deller: I appreciate your questions, Peter. Thank you.

Operator: There are no further questions in the queue.

Matthew Selinger: Operator, I am going to go ahead and read a couple, Colin, if you do not mind, from e-mail. I think you touched on this one, Colin, but the question is this. It is clear that large-scale orders may have been held back while the old guard in the energy business waited to be absolutely sure they would work as expected. So is this 26-burner startup likely to be a seminal event that opens the floodgates?

Colin James Deller: We believe so. And that is based on what we've been told from the clients. They are -- above everything else, they are waiting to see the technology running in somebody else's heater. So yes, the simple answer to that is yes, we believe so. We are just excited to be able to get out and talk about it.

Matthew Selinger: And Colin, in the past, the company, you have stated a kind of a break-even number of 160 burners a year. Do you believe that is obtainable potentially next year? Or is that a further target? What are your thoughts there?

Colin James Deller: Yes. That number was based on $100,000 per year, so $16 million run rate, right? The math works out to get the company to break even. We absolutely have the line of sight in the pipeline to get to that number. I mean, it is 3 or 4 process burner orders, a couple of flares, and then the runway with the M Series. It's a very pragmatic expectation for the company. That's the one question we can't guarantee is just the timing, right? But yes, the loads out there, the opportunities are definitely out there.

Matthew Selinger: With that, Colin, there are no more questions. So with that, I will hand the call back to you if you'd like any closing statements.

Colin James Deller: Great. Thank you very much. Thank you, everyone. I really appreciate you tuning in to this call and for your interest in ClearSign, especially taking your time and giving us your time this afternoon. We look forward to updating you regarding our developments and speaking with you on our Q4 and full year call in April next year. We don't plan on being quiet with news on them. So please continue to check in on the websites. We do encourage you to follow us on LinkedIn. Of course, when we have a significant announcement, we will be putting press releases out in addition to that. So thank you very much.

Operator: Thank you everyone. This concludes today's event. You may disconnect at this time and have a wonderful day. Thank you for your participation.

Should you buy stock in ClearSign Technologies right now?

Before you buy stock in ClearSign Technologies, consider this:

The Motley Fool Stock Advisor analyst team just identified what they believe are the 10 best stocks for investors to buy now… and ClearSign Technologies wasn’t one of them. The 10 stocks that made the cut could produce monster returns in the coming years.

Consider when Netflix made this list on December 17, 2004... if you invested $1,000 at the time of our recommendation, you’d have $315,271!* Or when Nvidia made this list on April 15, 2005... if you invested $1,000 at the time of our recommendation, you’d have $896,981!*

Now, it’s worth noting Stock Advisor’s total average return is 768% — a market-crushing outperformance compared to 198% for the S&P 500. Don't miss the latest top 10 list, available with Stock Advisor, and join an investing community built by individual investors for individual investors.

See the 10 stocks »

*Stock Advisor returns as of November 20, 2026.

This article is a transcript of this conference call produced for The Motley Fool. While we strive for our Foolish Best, there may be errors, omissions, or inaccuracies in this transcript. Parts of this article were created using Large Language Models (LLMs) based on The Motley Fool's insights and investing approach. It has been reviewed by our AI quality control systems. Since LLMs cannot (currently) own stocks, it has no positions in any of the stocks mentioned. As with all our articles, The Motley Fool does not assume any responsibility for your use of this content, and we strongly encourage you to do your own research, including listening to the call yourself and reading the company's SEC filings. Please see our Terms and Conditions for additional details, including our Obligatory Capitalized Disclaimers of Liability.

The Motley Fool has no position in any of the stocks mentioned. The Motley Fool has a disclosure policy.

Disclaimer: For information purposes only. Past performance is not indicative of future results.
placeholder
Gold Price Today: Can XAU/USD Hold $3,500? | Mitrade AUGold approaches US$3,500 as Fed tightening fears drive sharp weekly losses. Explore XAU/USD levels, Treasury yields and the outlook for Australian traders.
Author  Mitrade Team
9 hours ago
Gold approaches US$3,500 as Fed tightening fears drive sharp weekly losses. Explore XAU/USD levels, Treasury yields and the outlook for Australian traders.
placeholder
Australia’s jobs market just cracked — has the AUD/USD rate story flipped?Australia’s weakening jobs market is raising fresh questions about the RBA’s interest rate outlook and the Australian dollar. Explore why AUD/USD could be losing support, the key factors driving currency movements and what Australian forex traders should watch next.
Author  Mark Garro
14 hours ago
Australia’s weakening jobs market is raising fresh questions about the RBA’s interest rate outlook and the Australian dollar. Explore why AUD/USD could be losing support, the key factors driving currency movements and what Australian forex traders should watch next.
placeholder
Market News Today Australia: VIX Surges Nearly 16%, Gold Breaks US$3,600 and US Stocks SlideVIX jumps 15.8%, Nasdaq 100 falls 2.21% and gold slips below US$3,600. Explore Anthropic’s debut and the outlook for Australian CFD traders.
Author  Mitrade Team
14 hours ago
VIX jumps 15.8%, Nasdaq 100 falls 2.21% and gold slips below US$3,600. Explore Anthropic’s debut and the outlook for Australian CFD traders.
placeholder
Is Tech in a Bear Market? 20 Tech Stocks Fall Up to 76% From HighsAll 20 tech stocks on a list from financial newsletter The Kobeissi Letter trade at least 25% below record highs. CoreWeave (CRWV) leads the slide at 76%.Additionally, the S&P 500 has lost over $6 tri
Author  Beincrypto
15 hours ago
All 20 tech stocks on a list from financial newsletter The Kobeissi Letter trade at least 25% below record highs. CoreWeave (CRWV) leads the slide at 76%.Additionally, the S&P 500 has lost over $6 tri
placeholder
Gold and Bitcoin Are Falling. Peter Schiff Sees Opportunities for BothPeter Schiff says gold should not have fallen at all, while Bitcoin (BTC) has not fallen enough. The gold advocate calls the metal’s drop a buying opportunity and Bitcoin’s a selling opportunity.Both
Author  Beincrypto
15 hours ago
Peter Schiff says gold should not have fallen at all, while Bitcoin (BTC) has not fallen enough. The gold advocate calls the metal’s drop a buying opportunity and Bitcoin’s a selling opportunity.Both
goTop
quote